Ender 3 V2 BLTouch Firmware Installation Guide by Smith3D.com [Updated –13 November 2022]

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]

BLTouch Installation

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
If you are using a different extension wire, please pay attention to the wire colors above.

BLTouch Mount

BLTouch Mount for Ender3 V2 Link here (Use the two screws provided by BLTouch to screw it in.)

Firmware

* Last Update from Jyers has been 1 year ago, Professional Firmware has more features but setup guide maybe different.

The very first thing you should to is go into Control > Advanced and adjust Probe Offset X to -42 & Probe Y Offset -10 (Printed Mount). and Control > Store Setting.

If you are using Creality official BL-Touch set, you have to set it to Probe X Offset -44 & Probe Y Offset -6.

MountProbe X OffsetProbe Y Offset
Custom Mount V3-42-10
Creality Official Mount-44-6

Video Guide by CHEP : https://www.youtube.com/watch?v=TroPjdkSEOY (Video guide doesn’t include manual leveling, do make sure you do manual bed leveling after adjust the z offset)

Unless your system is well tuned, please use the firmware above instead of high speed. Slow Probe & 5 x 5, which is great for first time tuning.

[8th April] As for Smith3D firmware, we have depreciated our firmware & move on to Jyer firmware as it offer much better features & functionality.

For BTT Filament Sensor & Standard Filament sensor, do enable them
inside Control > Advanced > Filament Sensor/Runout Distance

If you have never change your motherboard, it’s 4.2.2 by default

For 4.2.2 5×5 (High Speed) – download here
For 4.2.7 Board 5×5 (High Speed) – download here
For more info regarding this release
For people who’s suffering random probe fails, please refer to the FAQ below for z switch port firmware.

If flashed & auto leveling doesn’t work, please reset configuration (Control > Restore Default) or try to flash again with different filename. If you are getting Black screen, do format your MicroSD Card to FAT32 and rename the firmware & try again.

Older Build (V1.3.5b)

If you are facing issue on newer builds, you may try the older build

What’s BL Touch High Speed Mode?

  • The high speed mode probes multiple points without stowing the needle, making it much much faster. But also prone to crashes if your bed is severely slanted. Please make good use of Manual leveling before you try this.

For Ender 3 V2 no bootloader installation is required. Copy the firmware into your SD card and then slot it in, the printer will begin flashing once you reboot it. Do remember that you need a different filename each time you flash a new firmware eg. firmware1.1bin > firmware1.2bin, else the system will ignore it.

For user who would prefer official firmware from Creality, you may check this guide here

Some UI customizations the community has added

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
For Manual Leveling, please refer to CHEP guide https://www.youtube.com/watch?v=_EfWVUJjBdA

Some other features were offered compared to Stock firmware

  • Turn on and off display during printing
  • PID Autotune Menu
  • Change Filament menu
  • Adjust probe offset, filament sensor in the menu
  • __h__m Time Format Setting

And remember to add “M420 S1” in Cura!

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
VERY IMPORTANT Add M420 S1; after the G28 in your start G-code in the starting G-code of your cura profile. To enable leveling on every prints. As the current marlin for Ender 3 V2 is unable to make “leveling enabled” persistent after reboot. M420 S1; Enable ABL (If you are getting error for Fade Height) This line of code always appear in other printer profile such as CR10SProV2/Ender5Plus where there is BLTouch built in.

You can also add G29 for Bed Leveling before every prints

Instead of adding the M420 S1 command above. You can replace it with G29 (Place it after G28). G29 basically starts a new round of auto bed leveling , good for users who would prefer a fresh bed leveling before every prints.

Nozzle Crashing Into Bed?

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]

Steps to produce a good leveling

  • Once you setup the Probe Offset X & Probe Offset Y, Store Setting and go to Prepare > Auto Home. Make sure your probe is directly at the center of the bed.
Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
Picture by CHEP
  • Start with Manual leveling to make sure the bed is leveled as much as you can, by manually adjusting bed spring. This is to reduce the amount of Z compensation ABL will need to apply when printing. Please refer to CHEP’s guide for how you can level your bed with a piece of paper. The firmware has included the buttons needed for printer to go to all 4 corners + center so you don’t have to do it via a gcode print file.
  • After the bed is leveled, get a good Z-offset by using the Prepare > Z-Offset. Remember to pre-heat your nozzle while using this as any remaining material stuck on nozzle tip might interfere the result while gauging with A4 paper. This tool will Auto home and then move Z to 0 to show actual Z offset. Prepare a paper to put between nozzle and bed, then try sliding it in and out, Microstep Up/Down & adjust Z offset until you feel a little friction between paper and nozzle. Use Home Z-Axis to double confirm if the z offset is the right one.
Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
Picture by CHEP
  • Once you got your Z offset, go to main menu and press “Leveling”. It will probe 5×5 points and save the mesh to your printer.
  • Done and start printing!
  • Again, it’s very important to heat up nozzle to 180-200 while using Z-offset (if there is PLA in nozzle) Else the Z-offset will vary a lot depending on the leftover material stuck on nozzle tip.

What if you are not getting an accurate Z Offset from the Tool? (Live Adjust Z Offset)

Sometimes moving the Z axis up and down bit by bit might cause a little slippages, which makes the Z-Offset gauging with A4 paper inaccurate.

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]
Picture by CHEP

If you want a better gauging result. We recommend user to adjust Z Offset via Tune during printing

FAQ

Z-axis won’t budge

Pay attention to the wiring color, some wires are inverted. If you are using 3rd party wiring, most probably the last two orange and yellow are inverted. You have to manually revert it back using a tweezer.

Black Screen of Death after flashed

Please follow this reddit link for full guide on how to do a proper flash
In summary
– Use newly formated sd card, with only bin file
– Rename bin file
– Unplug & reconnect power cord

Bltouch probe not centered / change probe offset

adjust Control > Advanced > Probe Offset X & Probe Offset Y

Manual Leveled & still printing in mid air or nozzle hitting the bed

Use slow probe 5×5 firmware to see if the situation is improving, if not check if your M420/G29 is added inside the start of gcode. Use either G29 or M420. Remember to save setting after leveled.

Sometimes Probe doesn’t finish during leveling

Solution 1:
Some users has issue with the bltouch port. the trigger signal or ground is not attached properly. Connect the two pin to the z switch stop & flash the firmware below.

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]

Download 2.0.x.17 ZSwitchStop 5×5 Fast Smith3d Marlin Firmware

Solution 2:
Try connect via Pronterface and check what’s the error code returned.

Summary (this reddit link explained in detail)
– Make sure bed not totally out of level, probe may out of reach or nozzle hit the bed first
– Check if your bed is badly warped
– Check if your bltouch pin is bent
– Check the XY axis wheel tension
– Check the Z axis for binding

Solution 3:
There is a resistor fix for this, you can solder a resistor and use the bltouch port.

Ender 3 v2 bltouch firmware installation guide by smith3d.com [updated –13 november 2022]

Setting is not saved

Remember to click “Control > Store Setting” everytime you setup completed. Check if eeprom is deleted in SD Card.

OctoPrint Settings

Power Lose Recovery doesn’t work

Power Lose Recovery only works when it reached certain layer. check your SD card if there is a PLR file exist. PLR determine if to display the Resume Printing message.

Motor making noises and freeze during print.

This will happen if you just flashed the firmware & does not reset the configuration. Just turn off and on your printer will do, restore default setting. Another possible issue is the dupont connectors on the motherboard loosen, do hot glue the connectors in place or upgrade it to 5 pin JST connector.

Sometimes UI/ print progress bar does not reflect to the latest

Known marlin bug. Restart, press back, will do.

Can I use 3DTouch or BLTouch older than v3.1?

May not compatible, this firmware is optimized for BLTouch v3.1.

Where can I get the source code? How to compile?

Github Repository is here.

If you are having issue compiling your own marlin, remember to set default_envs = STM32F103RET6_creality in platform.ini

How to donate?

Please donate to Marlin Firmware & https://www.paypal.com/paypalme/jyers. Without them, there will be no great firmware for Ender 3 V2

What happens If I don’t want a BLTouch anymore?

You may revert your firmware to the official non-BLTouch firmware downloadable via this link – https://www.creality.com/download/32

1,297 thoughts on “Ender 3 V2 BLTouch Firmware Installation Guide by Smith3D.com [Updated –13 November 2022]

  1. Kenneth says:

    Hello, just got a bltouch and it works properly but…
    Recv: Bilinear Leveling Grid:
    Recv: 0 1 2
    Recv: 0 -0.088 +0.017 +0.202
    Recv: 1 -0.125 -0.003 +0.165
    Recv: 2 -0.145 -0.062 +0.120

    above gives a perfect 0.2 print in 4 corners and middle (+/- 0.02).

    I can adjust to show level but won’t print right (smushed to bed, separates or doesn’t stick too high).
    Reset/redone literaly dozens of times. Flipped blt screw/nuts (same btw).
    Ideas?

  2. hi_puppy_12 says:

    I’m having a problem that I can’t find anything about online. I have a creality bl touch on my ender 3v2. The problem Im facing is that the probe comes down during the print to sense but it is doing so and hitting my print. Worse it will come down hitting the print making enough torque to of set the print. Its not telling it to offset it its like someone grabbed it so it docent move as much as it thought it did. I can’t find anything online about it so I’m trying here!

  3. alex says:

    Hi
    My CR level probe does not seem to work. I have tried many firmware settings but always the same, The hot end embeds itself onto the bed when trying to auto home or level. Do you think the CR probe is faulty ,
    with firmware with no auto level the machine works perfect. it did work for a while until i added a filament out detector , then it has never worked since , But i am sure its nothing to do with the filament sensor as i have never used it but disconnected it just in case

      • Alex says:

        Yes two wires from the CR touch were fused together, No idea why or how, but you could not see it, i only found them by using a multi meter .
        Thanks for the help.
        regards

  4. James says:

    I have the probe and nozzle set to center but when I run a bed level 5×5, it starts more offset (closer) to the left edge of the bed and it starts so close to the front of the bed that it touches the clip. Is there a way to change the start position of the bed leveling to get it centered to the bed?

  5. Anthony says:

    I have been using your firmware for a while, but I have a direct drive with an all metal hot end. Can you make this firmware but just bump the temp limits up for people with an all metal hot end? Thank you!

Leave a Reply to alex Cancel reply

Your email address will not be published. Required fields are marked *

Want a cookie?🍪 You can consent to have a better browsing experience.