Welcome Guest [ Login / Register ]

Operation continues as usual during MCO. Contact us at +6010-3443128 to arrange for same-day delivery within Klang Valley.
Operation continues as usual during MCO. Contact us at +6010-3443128 to arrange for same-day delivery within Klang Valley.

CR10 Smart : Buyer’s Guide 2

Congratulation for becoming a CR-10 Smart owner. This is an amazing medium size of CR-6 SE with remote printing & much sturdy build. Despite the amazing features of the machine, unfortunately the QC wasn’t done right & firmware wasn’t really ready yet. Fortunately the CR-10 Smart is a very simple machine to assemble and if you follow this guide you will be able to eliminate all initial issues to begin with.

Assemble the CR-10 Smart

Assembly is easy, just follow the video below to complete the assemble. The tool box including SD Card & Accessories is at the front panel of the printer. Make sure all the wires are plugged in.

Level the X axis (Recommended)

The very first thing after assembled, is the level your x axis, make sure left and right z are at the same height. My unit right is a little lower than left and we have to loosen the belt pulley, make sure both left and right is align.

Adjust the Hotend Eccentric Nut

This is very important step, CR-10 Smart is using Strain Gauge Leveling, the hotend I received is wobbling and it causes the leveling to push further down, it will scratch your glass bed or even damage your nozzle during your first print. Adjust the eccentric nut using a 8mm Spanner to tighten the wheel & make it less wobble. Not too tight.

Update Firmware (Optional)

The machine I received is using firmware 1.0.6 . The current firmware is lackluster compared to community firmware but at the moment it’s good to update it in case there are certain bug fixes. Below are the summary to update the firmware. DO NOT update if you don’t know what to do.

-SD Card (to flash motherboard firmware)
-MicroSD Card (1-16GB to flash screen firmware) (Anything lower and higher than that may not be able to flash, because you can’t set 4096 allocation unit)

Step 1 (Flash Screen Firmware with MicroSD)

1) Download the latest firmware from Creality website (At the moment is 1.0.8 Beta) or Here
2) Format the MicroSD Card into FAT32 4096KB (most important otherwise screen flashing will fail)
3) Copy the DWIN_SET folder into the root of the MicroSD Card
4) Open up the screen cover and insert the microSD from the screen.
5) Power on the printer & screen will light up blue
6) Wait for a few minutes until the printer screen display “END”, If the END happens within seconds, it means flashed failed.

Step 2 (Flash Motherboard Firmware with SD)

2) Format the SD Card into FAT32,
3) Extract and copy the content of the firmware.zip file into the roof of the SD Card
4) Insert the SD Card and hold Power On button.
5) Keep holding the power button until the Creality Logo animation moved. (about 10~15 seconds)
6) Check the firmware version by going into Setting > About Machine> Firmware version

Start CR-10 Smart & Level your bed

Once you are ready, press level & you are good to go. For safety and you doesn’t want to scratch your bed, you can go to the AUX Leveling, set Z offset to 0.3~0.4, and during start printing, only lower it down.

Insert filament through Filament Sensor

Insert the filament through the filament sensor, if you are having hard time to insert, do bend the end of the filament to another side & try again. Remember to open up the extruder arm when insert the filament, else you gonna struggle to put it in.

Creality Cloud (Updating)

This machine is heavily bind to the Creality Cloud so, to get the remote monitor print & monitor works, you must download Creality Cloud, register a profile, then scan & add the CR-10 Smart into the Device List.

3d printer

Connect Creality Camera to CR-10 Smart

Connecting Camera is never been easier, but only a few certified camera able to connect. Just plug in the USB port at the side and you are good to go!

Connect Camera USB to the USB port beside the LAN & Power button
That’s our simple setup


  1. Hello
    can i ask about the camera?
    wich types of camera can i connect?
    i need to update ot do something that it will work?
    Firmwere – HW 1.0.6
    Hardware – DWIN4.3

    1. No update needed for the camera, try update firmware for better leveling & performance.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Select your currency
MYR Malaysian ringgit